Getting ready for Indy . . .
-
Jim Diehl
- Master BucketHead

- Posts: 232
- Joined: Fri Jul 06, 2012 5:13 pm
- Handle: Top Hat
Re: Getting ready for Indy . . .
Spanky,
This story will be in the history books just like when you were elected president of the St. Louis Chapter while using the restroom.
You got to love it. Such rich history.
This story will be in the history books just like when you were elected president of the St. Louis Chapter while using the restroom.
You got to love it. Such rich history.
- Bill Cleveland
- Full Blown BucketHead

- Posts: 5150
- Joined: Fri Dec 21, 2012 2:57 pm
- Handle: Spanky
- Location: Saint Louis
Re: Getting ready for Indy . . .
Thanks, Jim. Got the front end put back together today with new bearings,(yes - packed with grease!) etc. Still need a new right front tire to replace the one I flat-spotted during my little adventure. Also dealing with a pesky oil leak. I think I'll replace my chrome oil pan with one of these . . . whaddaya think?


Spanky
- mike wade
- Full Blown BucketHead

- Posts: 5049
- Joined: Fri Jul 06, 2012 7:52 pm
- Handle: lincolnut
Re: Getting ready for Indy . . .
Bill if you will take a wire brush to that sealing surface on that Chrome oil pan you will stop that leak............you need to make that surface somewhat rough....................

TODAY IS THE OLDEST YOU'VE EVER BEEN, YET THE YOUNGEST YOU'LL EVER BE, SO ENJOY THIS DAY WHILE IT LASTS
- Bill Cleveland
- Full Blown BucketHead

- Posts: 5150
- Joined: Fri Dec 21, 2012 2:57 pm
- Handle: Spanky
- Location: Saint Louis
Re: Getting ready for Indy . . .
Windshield in place! Now . . . to fix that blankety-blank oil leak!!!


Have grease . . . will roll!!!



Have grease . . . will roll!!!
Spanky
- IdahoRelic
- Full Blown BucketHead

- Posts: 1120
- Joined: Tue Oct 13, 2015 11:55 am
- Contact:
Re: Getting ready for Indy . . .
Shapin' up and lookin' good, Mr. Bill

What size are the rear tires??????
What size are the rear tires??????
- Bill Cleveland
- Full Blown BucketHead

- Posts: 5150
- Joined: Fri Dec 21, 2012 2:57 pm
- Handle: Spanky
- Location: Saint Louis
Re: Getting ready for Indy . . .
They are 305/50-15's . . . BFG Euro TA's. I bought them a few years ago, Lyle, and I don't believe they make that size any more. 
Spanky
- IdahoRelic
- Full Blown BucketHead

- Posts: 1120
- Joined: Tue Oct 13, 2015 11:55 am
- Contact:
Re: Getting ready for Indy . . .
Thanks Bill. ahhhhhh, they look quite a bit wider than my 295's and you are correct, no longer available.Bill Cleveland wrote:They are 305/50-15's . . . BFG Euro TA's. I bought them a few years ago, Lyle, and I don't believe they make that size any more.
- Bill Cleveland
- Full Blown BucketHead

- Posts: 5150
- Joined: Fri Dec 21, 2012 2:57 pm
- Handle: Spanky
- Location: Saint Louis
Re: Getting ready for Indy . . .
Now . . . it runs good and drives well - time to complete some odds 'n ends and then . . . prep for paint!
I'm probably going to get tired of sandpaper before this is done!!! 




Spanky
- IdahoRelic
- Full Blown BucketHead

- Posts: 1120
- Joined: Tue Oct 13, 2015 11:55 am
- Contact:
Re: Getting ready for Indy . . .
Naw, cake walk to sand! Jack it up, find you a comfy rollin' chair, bucket of warm water, wet n' dry paper, a small 6-pack cooler and it'll all be done in 6 hours!

-
Jim Diehl
- Master BucketHead

- Posts: 232
- Joined: Fri Jul 06, 2012 5:13 pm
- Handle: Top Hat
Re: Getting ready for Indy . . .
Spanky, I like those rims.